/ Register

Red oak and maple dining room table

Discussion in 'Jims Woodworking' started by Coloman, Feb 17, 2008.

  1. Feb 17, 2008 #1
    Coloman

    Coloman New Member

    Messages:
    441
    State:
    Soddy Daisy, Tn
    Our new dinning room table. Its a butcher block top. It only took about 3 weeks to build and a quart of glue. I'm buying the chairs to match.
     

    Attached Files:

  3. Feb 17, 2008 #2
    CJ21

    CJ21 New Member

    Messages:
    4,303
    State:
    Montgomery, Alabama
    Very nice dining room table.
     

  5. Feb 17, 2008 #3
    lawnman61

    lawnman61 New Member

    Messages:
    1,694
    State:
    Fort Worth, Tex
    Is this the one I saw in progress at your house last week.
    Looking good.

    :cool2:
     
  6. Feb 17, 2008 #4
    catfishcrazy256

    catfishcrazy256 New Member

    Messages:
    2,648
    State:
    Indiana
    thats sharp , good job !!!!!!!!!!!!!:wink:
     
  7. Feb 17, 2008 #5
    Coloman

    Coloman New Member

    Messages:
    441
    State:
    Soddy Daisy, Tn
    Al
    Thats the 1.
     
  8. Feb 17, 2008 #6
    Catgirl

    Catgirl New Member

    Messages:
    13,546
    Yes it IS!!! Really pretty, nice work Bill. Thanks for posting. :cool2:
     
  9. Feb 17, 2008 #7
    Arkansascatman777

    Arkansascatman777 New Member

    Messages:
    7,782
    State:
    AR
    Great work Bill, thanks for posting :cool2:.
     
  10. Feb 17, 2008 #8
    ozzy

    ozzy New Member

    Messages:
    3,936
    State:
    Lost Wages
    Very nice work.
     
  11. Feb 17, 2008 #9
    alands94

    alands94 Active Member

    Messages:
    1,706
    State:
    Lebanon, I
    Very nice work Bill!
     
  12. Feb 17, 2008 #10
    CountryHart

    CountryHart New Member

    Messages:
    10,914
    State:
    missouri
    Nice job, it's pretty. I been ponderin the idea of making one from red cedar.
     
  13. Feb 17, 2008 #11
    Mike81

    Mike81 Well-Known Member

    Messages:
    4,186
    State:
    Alabama
    Great job! Thanks for the pics!!
     
  14. Feb 17, 2008 #12
    Dave L

    Dave L New Member

    Messages:
    1,012
    State:
    Minnesota
    Bill, very nice work there.
    Funny thing is, I was in heating and air before going all out woodworker.:big_smile:
     
  15. Feb 17, 2008 #13
    fish

    fish Active Member

    Messages:
    1,573
    State:
    ChattanoogaTenn
    Buddy, like I told you earlier, that is some fantastic work. Thanks for sharing with us Bill.
     
  16. Feb 18, 2008 #14
    Ketch

    Ketch New Member

    Messages:
    469
    State:
    Minnesota
    That's a fine looking table there Bill, thanks for sharing with us.
     
  17. Feb 18, 2008 #15
    beetle

    beetle New Member

    Messages:
    1,003
    State:
    Ohio
    Nice job on the table! What did you put on it for a finish?
     
  18. Feb 18, 2008 #16
    willcat

    willcat New Member

    Messages:
    2,463
    State:
    texas
    nice work on a nice table
     
  19. Feb 18, 2008 #17
    Coloman

    Coloman New Member

    Messages:
    441
    State:
    Soddy Daisy, Tn
    I used a water based polyacrlic. I put it on with a HVLP system that Jim ( fish) had suggested. About 6 coats with a light sanding in between standings.