fish sinker molding - best sinker mold made

Discussion in 'Terminal Tackle Review' started by boliver, Dec 15, 2005.

  1. boliver

    boliver New Member

    Messages:
    198
    State:
    Rudy Ark
    what is the best or your prefered brand of sinker mold.
     
  2. bigsammy

    bigsammy New Member

    Messages:
    189
    State:
    Poteau ok
    Do-it-molds for me.Kinda grew up with em and served me well for years.
     

  3. BAM

    BAM New Member

    Messages:
    827
    State:
    Tennessee
    The only ones I have used are the Do-it brand. Have several and no complaints.
     
  4. boliver

    boliver New Member

    Messages:
    198
    State:
    Rudy Ark
    thanks i bought a palmer first and it is fair and some no name it is terrible have recently bought do-it and they are very tight but havent tried them yet.thanks again
     
  5. Leakyboat

    Leakyboat New Member

    I use Do-it,no complaints either!
    Ernie
     
  6. Phil Washburn

    Phil Washburn New Member

    Messages:
    7,680
    State:
    Shawnee OK
    yep, do-it is the one...and by the way, i still have a lot of lead i'd gladly give to a BOC member that wants it - no shipping tho....strictly on site pickup :D
     
  7. on_the_fly

    on_the_fly New Member

    Messages:
    606
    State:
    Kentucky
    yep do-its is the way to go i also have a palmer an its a good mold to.
     
  8. Desperado

    Desperado Active Member

    Messages:
    1,244
    State:
    Pataskala, Ohio
    Name:
    Clarence
    I use Do-it molds and Hilts molds for all my sinkers.
     
  9. misterwhiskers

    misterwhiskers New Member

    Messages:
    273
    State:
    Trenton
    Will someone go pick that lead up from Phil,and ship it over to me?

    I need to get to the mechanics and picke me up some more lead.they're pretty good resource,can get about 4 pounds or more of lead from old tire weights for a couple bucks!

    Oh,Do It molds,haven't seen a better one yet.You'll enjoy it I'm sure.
     
  10. joesf

    joesf New Member

    Messages:
    283
    State:
    Bloomington IL
    I hope you mean 40 pounds. The going rate for clean lead is about $.28 a pound. Wheel weights are about $.17 a pound.
     
  11. H2O Mellon

    H2O Mellon New Member

    Messages:
    3,012
    State:
    Ohio
    Do-It Molds for me. I have some Palmers & some other brands too, but after winter I will be selling them, I am only sticking w/ Do-It Molds.
     
  12. TOPS

    TOPS New Member

    Messages:
    4,099
    State:
    Cabot,Arkansas
    I got mine from CC. It is out in my shed and I do not know what the brand name is. It the no-roll molds that CC sell. :confused:
     
  13. H2O Mellon

    H2O Mellon New Member

    Messages:
    3,012
    State:
    Ohio
    It's prob a Do-It Mold, I think thats the only brand they sell.
     
  14. jobuck202

    jobuck202 New Member

    Messages:
    2
    easy way, punch holes in the ground, size you want,
    stick a wire loop in the bottom with top of loop above ground,
    fill with hot lead.
    with about ten holes make a batch real fast.
    instead of a loop, can use a swivel same way.
    nothing against molds, just an easy way.
    ,,,,Ray
     
  15. canebreaker

    canebreaker Well-Known Member

    Messages:
    1,307
    State:
    Southaven,MS
    I know of a web site that sells cheaper than do-it and CC. If you want it, send me a message. Another site with production pots too.
    Ebay sellers get as much as new ones.